Vastera VA-103 Installation Manual

Relion® Protection and Control650 seriesIEC 60870-5-103 Communication ProtocolManual

Selection of standard information numbers in controldirection...55

Section 1 Introduction1.1 This manualThe communication protocol manual describes a communication protocolsupported by the IED. The manual concentrat

1.3 Product documentation1.3.1 Product documentation setPlanning & purchaseEngineeringInstallingCommissioningOperationMaintenanceDecommissioning

well as verifying settings by secondary injection. The manual describes the processof testing an IED in a substation which is not in service. The chap

Documents related to REB650 Identity numberProduct Guide, configured 1MRK 505 265-BENType test certificate 1MRK 505 265-TEN Documents related to REL

650 series manuals Identity numberCommunication protocol manual, DNP3 1MRK 511 241-UENCommunication protocol manual, IEC 61850 1MRK 511 242-UENCommuni

• LHMI messages are shown in Courier font, for example:To save the changes in non-volatile memory, select Yes and press .• Parameter names are shown

Table 2: Backup protection functionsIEC 61850 / Functionblock nameANSI Function description Current protectionPHPIOC 50 Instantaneous phase overcu

Table 3: Control and monitoring functionsIEC 61850 / Functionblock nameANSI Function description ControlSESRSYN 25 Synchrocheck, energizing check

IEC 61850 / Functionblock nameANSI Function description I103POSCMD IED commands with position and select for IEC60870-5-103Secondary system supe

IEC 61850 / Functionblock nameANSI Function description VMMXU Phase-phase voltage measurementCMSQI Current sequence component measurementVMSQI

Table 4: Designed to communicateIEC 61850 / Function blocknameANSI Function description Station communicationIEC61850-8-1 IEC61850 communication

IEC 61850 / Functionblock nameFunction descriptionDTSBEGIN Time synchronizationDTSEND Time synchronizationTIMEZONE Time synchronizationIRIG-B Time syn

Section 2 IEC 60870-5-103 overview2.1 IEC 60870-5-103 standardIEC 60870-5-103 is defined as a companion standard for the informative elementof prote

standard. It should also be noticed that these sets of data are mainly defined for asingle function protection IED. 650 series IEDs in turn are multi

module, the only hardware needed is optical fibres (glass/plastic) and an opto/electrical converter for the PC/RTU.Table 7: Max distances between IED/

20

Section 3 IEC 60870-5-103 communicationengineering3.1 IEC 60870-5-103 engineering in PCM600The Application Configuration tool (ACT) and the Paramete

The general settings for IEC 60870-5-103 communication are the following:• SlaveAddress and BaudRate: Settings for slave number and communicationspeed

First, set the IED to be synchronized via IEC 60870-5-103 either from IEDConfiguration/Time/Synchronization/TIMESYNCHGEN:1 in PST or from thelocal HMI

Document ID: 1MRK 511 243-UENIssued: February 2011Revision: -Product version: 1.1© Copyright 2011 ABB. All rights reserved

24

Section 4 IEC 60870-5-103 vendor specificimplementationThe signal and setting tables specify the information types supported by the IEDswith the comm

GUID-B8A3A04C-430D-4488-9F72-8529FAB0B17D V1 ENFigure 5: Settings for CMMXU: 1All input signals to IEC 60870-5-103 I103MEAS must be connected in appli

4.1.1.3 SignalsTable 9: I103MEAS Input signalsName Type Default DescriptionBLOCK BOOLEAN 0 Block of service value reportingIL1 REAL 0.0 Service value

The IED reports all valid measuring types depending on connected signals.Upper limit for measured currents, active/reactive-power is 2.4 times rated v

4.1.2.3 SignalsTable 11: I103MEASUSR Input signalsName Type Default DescriptionBLOCK BOOLEAN 0 Block of service value reportingINPUT1 REAL 0.0 Servic

Function type parameter for each block in private range. Default values are definedin private range 25 – 27. One for each instance.Information number

4.1.3.4 SettingsTable 14: I103AR Non group settings (basic)Name Values (Range) Unit Step Default DescriptionFunctionType 1 - 255 - 1 1 Function type

4.1.4.3 SignalsTable 15: I103EF Input signalsName Type Default DescriptionBLOCK BOOLEAN 0 Block of status reporting51_EFFW BOOLEAN 0 Information numb

The delay observed in the protocol is the time difference in between the signal thatis triggering the Disturbance Recorder and the respective configur

CopyrightThis document and parts thereof must not be reproduced or copied without writtenpermission from ABB, and the contents thereof must not be imp

Name Type Default Description73_SCL REAL 0 Information number 73, fault location in ohm74_FW BOOLEAN 0 Information number 74, forward/line75_REV BOOLE

Info. no. Message Supported TYPE GI COT64 Start phase L1 Yes 2 Y 1,7,965 Start phase L2 Yes 2 Y 1,7,966 Start phase L3 Yes 2 Y 1,7,967 Start residual

4.1.6.2 Function blockIEC10000292-1-en.vsdI103IEDBLOCK19_LEDRS21_TESTM23_GRP124_GRP225_GRP326_GRP4IEC10000292 V1 ENFigure 11: I103IED function block4

Info. no. Message Supported23 Setting group 1 active Yes24 Setting group 2 active Yes25 Setting group 3 active Yes26 Setting group 4 active Yes4.1.7

4.1.7.4 SettingsTable 22: I103SUPERV Non group settings (basic)Name Values (Range) Unit Step Default DescriptionFunctionType 1 - 255 - 1 1 Function t

GUID-391D4145-B7E6-4174-B3F7-753ADDA4D06F V1 ENFigure 13: IEC 60870-5-103I103USRDEF:14.1.8.2 Function blockIEC10000294-1-en.vsdI103USRDEFBLOCK^INPUT1

4.1.8.4 SettingsTable 24: I103USRDEF Non group settings (basic)Name Values (Range) Unit Step Default DescriptionFunctionType 1 - 255 - 1 5 Function t

4.2 Commands in control direction4.2.1 Function commands for IEC 60870-5-103 I103CMD4.2.1.1 FunctionalityI103CMD is a command function block in con

4.2.1.5 Supported information typesFunction commands in control direction, pre-defined I103CMDNumber of instances: 1Function type is selected with pa

4.2.2.4 SettingsTable 30: I103IEDCMD Non group settings (basic)Name Values (Range) Unit Step Default DescriptionFunctionType 1 - 255 - 1 255 Function

DisclaimerThe data, examples and diagrams in this manual are included solely for the conceptor product description and are not to be deemed as a state

4.2.3.3 SignalsTable 31: I103USRCMD Input signalsName Type Default DescriptionBLOCK BOOLEAN 0 Block of commandsTable 32: I103USRCMD Output signalsNam

Function type for each function block instance in private range is selected withparameter FunctionType. Default values are defined in private range 1

4.2.4.4 SettingsTable 36: I103GENCMD Non group settings (basic)Name Values (Range) Unit Step Default DescriptionFunctionType 1 - 127 - 1 1 Function t

4.2.5.3 SignalsTable 37: I103POSCMD Input signalsName Type Default DescriptionBLOCK BOOLEAN 0 Block of commandPOSITION INTEGER 0 Position of controll

include the function type and the information number for each signal. Formore information on the description of the Disturbance report in the Technica

This section describes all data that is not exactly as specified in the standard.ASDU23In ‘list of recorded disturbances’ (ASDU23) an information elem

50

Section 5 Interoperability5.1 Physical layerTable 39: Electrical Interface SupportedEIA RS-485 Nonumber of loads No5.1.1 Optical interfaceTable 40

5.2.2 Common address of ASDUTable 42: Common address of ASDU SupportedOne COMMON ADDRESS OF ASDU (identicalwith station address)YesMore than one COM

5.2.3.3 Supervision indications in monitor directionTable 45: Supervision indications in monitor directionINF Semantics Supported32 Measurand supervi

ConformityThis product complies with the directive of the Council of the EuropeanCommunities on the approximation of the laws of the Member States rel

INF Semantics Supported84 General start/pick-up Yes85 Breaker failure Yes86 to88Trip measuring system L1 to Trip measuringsystem L3Yes89 Trip measurin

5.2.4 Selection of standard information numbers in controldirection5.2.4.1 System functions in control directionTable 51: System functions in contro

5.2.5 Basic application functionsTable 54: Basic application functionsSupported Yes Test modeNo Blocking of monitor directionYes Disturbance dataNo

DRA#-Input ACC IEC103 meaning5 5 UL16 6 UL27 7 UL38 8 UN9 64 Private range10 65 Private range11 66 Private range12 67 Private range13 68 Private range

58

Section 6 GlossaryAC Alternating currentACT Application configuration tool within PCM600A/D converter Analog-to-digital converterADBS Amplitude deadb

CPU Central processor unitCR Carrier receiveCRC Cyclic redundancy checkCROB Control relay output blockCS Carrier sendCT Current transformerCVT Capacit

FOX 20 Modular 20 channel telecommunication system for speech,data and protection signalsFOX 512/515 Access multiplexerFOX 6Plus Compact time-division

I-GIS Intelligent gas-insulated switchgearInstance When several occurrences of the same function are availablein the IED, they are referred to as inst

apparent impedance to the fault applied to the balance point,that is, the set reach. The relay “sees” the fault but perhaps itshould not have seen it.

Table of contentsSection 1 Introduction...5This manual...

SMA connector Subminiature version A, A threaded connector with constantimpedance.SMT Signal matrix tool within PCM600SMS Station monitoring systemSNT

dissemination of standard frequencies and time signals. UTCis derived from International Atomic Time (TAI) by theaddition of a whole number of "l

66

67

Contact usABB ABSubstation Automation ProductsSE-721 59 Västerås, SwedenPhone +46 (0) 21 32 50 00Fax +46 (0) 21 14 69 18www.abb.com/substationautomati

Settings......31Supported information types...

Signals.....................42Settings............